Manual scraping method to correct the precision of linear guide rail: there are many mechanical methods to correct the precision of linear guide rail, but in the absence of conditions in the factory, what is the best way to correct the precision of linear guide rail? The process scraper guide rail is still the main technology to restore the precision of guide rail. After scraping the guide rail of the machine tool, it not only has high precision, good wear resistance, good oil storage conditions, but also has beautiful stripes under the refraction of the light due to the regular arrangement of knife flowers. The process scraper does not need large equipment and is not limited by the guide rail structure. Especially in the maintenance of precision machine tools, due to the high precision of linear guide rail, high requirements of movement stability, and long service life. Moreover, the guide rail of precision machine tool is not too worn, and it is usually repaired on the original basis! The guide screw manufacturer will introduce the manual scraping method in detail for you:

　　一、刮板導軌本準則采用合理的刮板方法，既能保證和提高刮板質量，又能明顯提高生產功率，所以，無論是新制造的機床還是修理機床，都應符合以下準則。

　　1、 This standard adopts a reasonable scraper method, which can not only ensure and improve the scraper quality, but also significantly improve the production power. Therefore, whether the newly manufactured machine tool or the repair machine tool, it should meet the following standards.

　　1、要選擇墓穴時刮準導軌，通常選擇較長、自由度更約束、較難刮支撐的導軌作為基準導軌。

　　1、 First of all, it is necessary to select the guide rail when the tomb is scraped. Generally, the guide rail with longer length, more restricted freedom and more difficult to scrape and support is selected as the reference guide rail.

　　2、關于機床導軌的大修，要了解刮削前機床的磨損情況，導致機床導軌元件變形，并在刮削時要考慮并采取措施。在舒適的環境下磨牙。對拉緊過緊的地腳螺母松馳，由拉緊螺母壓力過大而引起機床導軌變形，從而引起機床內應力恢復不正常。

　　2. For the overhaul of machine tool guide rail, it is necessary to understand the wear condition of machine tool before scraping, which leads to the deformation of machine tool guide rail components, and to consider and take measures during scraping. Grind your teeth in a comfortable environment. Loosen the anchor nut which is too tight, and cause the deformation of the guide rail of the machine tool due to the excessive pressure of the tension nut, thus causing the abnormal recovery of the internal stress of the machine tool.

　　3、刮床導軌，通常應在刮床裝置上的著落板上，用調節墊來調節機床裝置的水平，在更佳的情況下，這樣才能保證精度，把刮刮量控制在更小!

　　3. The guide rail of scraping machine, usually on the landing plate of scraping machine device, is used to adjust the level of machine device by adjusting pad. In the best case, this can ensure the accuracy and control the scraping amount to the minimum!

　　4、左右導軌組合各外形的刮磨應先刮大平面，再刮小平面。先刮硬表面，再刮易表面，先刮剛性好的表面，再刮剛性差的表面!

　　4. For the grinding of left and right guide rail combination, the large plane shall be scraped first, and then the small plane. First scrape hard surface, then easy surface, first scrape the surface with good rigidity, then scrape the surface with poor rigidity!

　　以上是導軌絲杠廠家為大家介紹的相關內容，想要了解更多內容，歡迎訪問網站：http://www.shrsensor.comThe above content is introduced by the guide screw manufacturer. For more information, please visit the website: http://www.jgongrun.com